破碎机,制砂机,圆锥破碎机

　　产品概述/Productoverview

　　大块状物料经颚式破碎机破碎到所需粒度后，由提升机将物料送至储料斗，再经电磁振动给料机将物料均匀定量连续地送入主机磨室内进行研磨。粉磨后的物料被风机气流送入选粉机内进行分级，在选粉机叶轮的作用下，不符合细度要求的物料落入磨室内重新辗磨，符合细度要求的物料则随气流经管道进入旋风集粉器内，进行分离收集，经排料装置排出即为成品粉体。分离后的气流通过旋风集粉器上端回风管进入风机，该系统属于闭路循环系统，并在正负压状态下运行。

　　After the bulk material is crushed to the required size by jaw crusher, the material is sent to thestorage hopper by the elevator, and then the materialis evenly and quantitatively sent to the main machinegrinding chamber by the electromagnetic vibration feeder for grinding. The miled materials are sent intothe separator by the fan air flow for classification. Under the action of the impeller of the separator, thematerials that do not meet the fineness requirements fall into the grinding chamber for re grinding. Thematerials that meet the fineness requirements enter the cyclone collector with the air flow through thepipeline for separation and collection. The finished powder is discharged through the discharge device.The separated air flows into the fan through the return air pipe at the upper end of the cyclone collector.The system is a closed-circuit circulation system and operates under positive and negative pressure.

　　产品概述/Productoverview

　　大块状物料经锤式破碎机破碎到所需粒度后，由提升机送入料仓，经给料设备均匀连续的喂入主机内部，进入主机的物料随倾斜的导流管到主机转盘上部的散料盘上。主机工作时，几十个磨辊这环道内旋转、滚动。而物料在离心力作用下被散料盘散向周边并落入磨腔，在环道内被磨辊冲压、滚辗、研磨。经过多层粉碎辗磨后的物料，随风机气流送入选粉机内进行粉体分级，在选粉机叶轮的作用下，不符合细度要求的物料落回磨腔内重新辗磨，符合细度要求的物料则随气流进入旋风集粉器内进行分离收集，并由底部的卸料装置排出即为成品粉体，其余部分的粉体则从旋风集粉器上部进入脉冲除尘器内，并粘附在滤袋表面，脉冲阀控制高压气流使其瞬间喷吹到滤袋内部引起滤袋剧烈膨胀波动，通过滤袋的突然抖动弹落粘附的粉体，掉落在除尘器下部的粉体，经螺旋输送机讲两处收集的粉体进行汇集排出即为成品。过滤后的气流随风机经过消音器排放到空气中。，该系统属于开路系统，在负压状态下运行。

　　After being crushed to the required size by hammer crusher, the bulk material is sent into the silo bythe elevator, and then evenly and continuously fed into the main machine through the feeding equipment.The material entering the main machine is sent to the bulk plate on the upper part of the main machineturntable with the inclined guide pipe. When the main engine is working, dozens of grinding rollers rotateand roll in the ring. Under the action of centrifugal force, the material is scattered to the periphery by thebulk plate and falls into the grinding cavity, and is punched, rolled and ground by the grinding roller in thering. After multi-layer crushing and grinding, the material is sent into the powder concentrator with the airflow of the fan for powder classification. Under the action of the impeller of the powder concentrator, thematerial that does not meet the fineness requirements falls back into the grinding chamber for re grinding.The material that meets the fineness requirements enters the cyclone collector with the air flow forseparation and collection, and is discharged by the discharge device at the bottom, which is the finishedpowder, The rest of the powder enters the pulse dust collector from the upper part of the cyclone collectorand adheres to the surface of the filter bag. The pulse valve controls the high-pressure air flow to make itinstantly blow into the filter bag, causing the filter bag to expand violently and fluctuate. The adherentpowder will bounce off through the sudden shaking of the filter bag and fall into the lower part of the dustcollector, Through the screw conveyor, the powder collected at two places is collected and discharged tobe the finished product. The fitered air is discharged into the air with the fan through the muffler., Thesystem belongs to open circuit system and operates under negative pressure.